Sunday, February 6, 2022

HP Z3801A GPS "SmartClock" Repair

 So there I was.....

With apologies to juvat over at The Chant....

As part of the electronics shop "upgrade", I dug out my old HP "SmartClock", which is a GPS-based time and frequency standard. I've had this little box for around 20 years, and it always worked flawlessly. I originally bought it to use as high-accuracy portable clock to synchronize my laptop clock for portable satellite operation, as well as give me an accurate LAT/LON position to enter into my satellite tracking program. Kinda killed two birds with one stone. It also has a VERY good 10MHz timebase in it, which I had plans to use, but never did. These were originally made for use at cellphone towers, where accurate time was used for billing and hand-off timing between towers.

The neat thing about the 10MHz timebase is that it's not only an HP "Double Oven" oscillator, but it's also "GPS Disciplined", meaning it gets locked to the extraordinarily accurate clocks in the GPS satellites, and provides a 10MHz signal that accurate to something like one part in 10e12. Crystal oscillators are about "as good as it gets" for short-term stability, but can, and usually do, drift over time. Part of the GPS signal is a one-pulse-per-second (aka "1pps") timing hack that's ONE SECOND, by God. Well, about as good as He lets us make for now.  How the GPSDO works is explained in the link above, so I won't go into it here.

Anywhoo.....When I plugged it in some years back, none of the lights came on, so I shelved it until I could a round tuit. Opened it up the other night, and started poking around to figure out why it wasn't powering up. The supply was good, but no blinky lights. Then I noticed this:

Well there's your problem....One of the Molex contacts came loose in the housing, and slid out of position when the housing was plugged into the board.

Easy-peasy fix. Pry the tiny locking tab out a bit, snap the contact back in the housing, and reconnect.

Fixed and ready to plug back in.

The next step was finding the old software I had, and then getting it to run on Windows 7, which is still a "Work In Progress". In the meantime, I was able to connect to the clock using a terminal program, and an RS232-to-USB adapter. Two issues with older GPS units is that if the clock has been turned off for ~90 days, and/or moved a few hundred miles, it won't have a proper list of satellites to look for when it's turned back on.

This one's been off for at least 4 years, and has moved 1100 miles since it was last used. In that case, you have to tell the device to run a "Sky Survey", and collect a current almanac from a satellite ASAP. So, connecting to the clock, I sent ":gpsystem:survey once", so it would grab the first satellite in view, and get an almanac. With a GPS antenna sitting in the basement window, it was able to do this, barely, and at least get itself locked to two satellites.

So it's just sitting there now collecting data, and begging me for a better antenna, which will have to wait for Spring when I can drill another hole through the foundation (poured concrete) and snake a new cable into the basement.


And I'm still waiting for the photocells I need to finish the THD Analyzer. USPS says they cleared Denver this morning, so hopefully I'll get them tomorrow.

Have a happy and blessed Sunday!




14 comments:

  1. For software? Lady Heather
    http://www.ke5fx.com/heather/readme.htm

    ReplyDelete
    Replies
    1. THANKS! I've never seen that one before. I'll try it a bit later.

      Delete
    2. Used to belong here - fascinating group. Got too many other hobbies:
      http://www.leapsecond.com/time-nuts.htm

      Delete
    3. Yeah the Time Nuts. I knew some of those guys when I lived in SoCal. I think Dennis Kidder was in the group. Got the Lady Heather installed, and it works great! Does everything I want it too, and worked immediately after I edited the cfg file. Thanks again!

      Delete
  2. Congratulations, drjim.
    You all be safe, stay warm and God bless.

    ReplyDelete
    Replies
    1. Thanks, Linda. The weather here is going to be upper 40's this week, and sunny.

      Delete
  3. It's amazing to me that in just the few years since I was in the aerospace mill that technology has placed standards in so many places. We used to depend on NIST to provide those standards in the past.

    ReplyDelete
    Replies
    1. The only place I worked at that had a 10MHz reference signal piped all over the plant was Western Electric. I got to be friends with Equipment Tech when I worked there, and he showed me the rack of HP equipment used to produce it. Had a 10 MHz "Double Oven" OCXO, which was phase-locked to the WWVB signal at 60kHz. Had one of those fancy 10-turn pot dials that looked like a little clock; a Big Hand for the units, "Cycles-per-Second", and a Little Hand for "Tens of Kilocycles". Looked like it belonged on a USN ship! Now we have clocks in orbit that are 99% as good as the best Earth-bound clocks, and they broadcast timing signals we can use to synchronize a good, old "Double Oven" Quartz oscillator!

      "Primary Standard" accuracy in your very own basement.....

      Delete
  4. That sounds like a really neat piece of equipment. Glad you could resurrect it. Must have been like working on a Porche after futzing with the Heathkits.

    Drilling through the foundation. Sounds like fun. Have you considered boring a big hole and consolidating all the cabling and allowing for future antennae growth?

    ReplyDelete
    Replies
    1. Yeah, it's a really mind boggling piece of gear when you think about it and what it does. Yes. it's very nicely made, with the best quality circuit boards and premium components. Definitely NOT consumer-grade stuff.

      Before I set up the radio room in the sun room, it was going to be in one-half of the "shop area" of the basement. I was going to get a 3" hole cored into one wall, and run a 3" plastic conduit from the hole to the shop. Would have been more than adequate for my needs. Now I'm just going to get some masonry bits about 3/8" or 1/2", and make a hole through the concrete like the cable TV company did. Pull one RG-6QS through it, and seal it with RTV. If I need to, I can duplex a wide-band antenna on that one cable for a scanner, while also passing the DC power for the GPS antenna, and bringing the GPS signal down.

      Delete
  5. Replies
    1. "Yea, though I walk through the Valley of Unfinished Projects, I shall fear no evil"...or something like that...

      Delete
  6. Hmmmm. I for one look forward to your new command and control center.

    ReplyDelete

Keep it civil, please....

Gloomy, Gritty, Grey Day

 At 1700 local it's as described in the headline; 30*F, 88% RH, completely overcast, snowing like crazy (small flakes, but lots of them)...