Flow Snurries and COLD!

 It's 20* at 1640 local, and we have about 2" on the snow table. The NWS is predicting another 2~4" overnight, with temps going down to low single digits.

Be a real good night for a mug of hot coffee, and some work in the basement. The big SX-980 receiver is back on the bench, and I'm doing the basic checks again, as it's been like six months since I last touched it, except to move it. So far, so good. I'm aware of some of the issues, but a new one cropped up in that the FM Stereo drops out, but comes back when things are gently tapped. I know, another intermittent to track down!

Well, that was easy. Went down to take the pic, turned it on (no FM...) and then punched the select button between AM and FM, and the FM came back! OK....another dirty switch to clean....le sigh... I should have cleaned them all when I had the panel off, but it's moot now because I have to take the panel off again to clean the dial properly. 

And an update on the Great Rye Bread Experiment of two weeks ago. I made two mistakes, one major, one minor. The major mistake was not giving it a full second raise. As a result, it came out a bit denser than it should. The flavor was wonderful, but a bit too dense. The minor mistake was not dividing the dough into two loaves before the second raise. It made HUGE (2 pound) loaf of bread:

Sure was tasty, though. This weekend I'm going to make it again, and correct the two mistakes I made. And I've collected enough bacon grease to make two batches of Skillet Cornbread, one test batch, and one batch for Thanksgiving dinner if the test article doesn't self destruct....

Jay Leno Suffers Serious Burns In Car Fire

 Jay is a good guy to the car community. He supports many educational programs, and gives freely of his time and money.

Full details on the Hagerty website.

 

Please say a prayer for Mr. Leno.

Wonder Who's Lurking In The Gulf.....

 Interesting ground track of a Boeing E6,  tail number 16-4404.

 

Thank You To All Veterans

 Thank you all for your service and sacrifice.

Hang In There...It'll Be TGIF Before You Know It...

 And I've been keeping busy doing some yard work some wood cutting/splitting/stacking, cleaning the house for SLW, and just enjoying a nice, quiet, mundane life.  BTW...the new Hammer Drill splits small logs quite well, once they're dried. And it drove the ground rods in quite well, too.

Took the Supra out the other day for a couple of hours, and came back all invigorated. It's not a powerful car, with only 165HP in a 3,000 pound car it can't be, be it's very rewarding to drive it quickly. It's an "Analog Car" without Traction Control, ABS, Air Bags, or any of the other electronic nannies today's cars have. With the suspension work I did it corners extremely flat and predictably, and the larger, wider wheels with modern low profile tires give it an astounding amount of grip. The upgraded brakes are so good I constantly worry about getting rear-ended in traffic, as almost happened a couple of times back in Long Beach. Still have a bunch of cosmetic and interior work to do, along with some well overdue maintenance items (cam drive belt & tensioner, for one), but I don't want it off the road again as long as it was last time, so I'll portion out the remaining mechanical work into "weekend sized" chunks, and get the tasks crossed off as I do them.

The Pioneer cassette deck is on hold for now, pending some discussion with Those Who Know About These Things. I have a few things to try based on suggestions, but for now it's off the bench, as I really, really, really want to get my SX-980 receiver finished and back in service. I was almost finished with it, and then I found some scratchy, noisy switches that (still) need cleaning, and as I was doing the dial alignment, I noticed I hadn't properly cleaned all the dial behind the glass. Since that requires pulling the front panel (again), which is also required to get at the dirty switches, I put the project on hold while I did the Great Heathkit Audio Analyzer Rebuilds, which wound up taking months longer than I anticipated. I learned a tremendous amount in rebuilding the two analyzers, both honing my tech skills and i understanding how the measurements are made, which leads to a better understanding of what the measurement is all about. Worthwhile, but very time consuming.

And then I decided to get a cassette deck.......what was I thinking?

Anywhoo, just been hanging out with Pebbles while SLW is out, and using the fireplace a lot. I spent a couple of hours figuring out how the pull-screens in it work, and why they were so awkward to use. Turns out a couple of places had come unraveled, and were dangling about getting snagged on each other. I double twisted a few inches of stainless picture hanging wire, strung it through the floppy parts, and secured it off by twisting the ends together. Works fine, and now I can easily slide the screens back-and-forth.

And it beats paying $300+ for a whole new glass door/screen assembly, as I can't seem to find just the replacement sliding screens.

It's Not Monday, and It's Not Stormy, but I Like This Song....

 Overcast and 45* outside today. Was going to either take the Supra out, or do yard work, but Da Wedder ain't conducive to either.

SO......I'm going to bake some bread, and listen to music today. Have a nice fire and watch a movie later. SLW is up in BC with friends, so it's pretty quiet here. Just me and the dog....

Hope you all have a pleasant and blessed Sunday.

First "Real" Snow Of The Season

 We had some snow showers last week that covered the grass, but it was gone by 0900.

This started around 1600, and went until about 1900. Looks like about 2" on the snow table.

 Supposed to get another 2" tonight, but we'll see. Temps will be in the low 20's at night, so looks like Winter approacheth!

Only In Colorado....

 Do you hear a police call on the scanner for "Two Men Driving A Large White Truck Chasing A Deer Around A Traffic Circle....."

I think it's better than hearing of another 7-11 getting knocked over in Lost Angeleez.......

BOOOOO!!!! Happy Halloween!

 Hope all the little ghost and goblins out tonight reap their harvest of Fall Candy!

Be Safe!

Annnnnd..... The Pioneer CT-F950 is Still Messed Up.

 As soon as I put the front panel back on the CT-F950 deck the transport problems started again.

SOOOOO.....At this point I'm going to set it aside while I contact a guy on the AudioKarma forum who rebuilds the Reel Hubs and Spindles. The consensus is mine are excessively worn, and need to be refurbished. New clutch pads, replace any broken parts, test them, and send them back. I'm not sure what he charges, but it appears to be reasonable per other forum members.

Besides....I've had my SX-980 receiver on the back burner WAY too long, and I need to get going on it again.

Huh.....I Think I Fixed It....

 Spent a few hours going over the Pioneer CT-F950 cassette deck. I wicked all the solder off the switch connections, cleaned the board, and resoldered them all. I also went back over the areas of the board where I reflowed some of the connections that didn't look quite right, and yep....I caused a solder short in the right channel, effectively shorting the signal from the tape to ground. Cleaned all those up, and it appears to work.

Here it is playing an old Van Halen tape I paid a buck for.

Sounds good through the headphones, too. All the scratchy/screechy noise the switches caused is gone, and the switches work very smoothly now.

Now I can go through the Electronic Alignment procedure, set all the levels, and test it to see if it meets specs.

After that's finished and it's all cleaned up, I think I'm going to send it down the road. I just don't trust it as far as reliability goes. I just want to put a tape in it, or make a tape with it, to listen to. I don't want this back on the bench every 3 or 4 months.....