All Battened Down

 Made a run to the store to pick up some extra stuff, and some essential stuff, like COFFEE, and rawhide chews for Pebbles The Wonder Dog. She gets quite insistent if she doesn't get her morning rawhide, but the evening rawhide is not a daily treat.

As of 2330, it's overcast, but dry. Got hit by a few raindrops when we were out earlier, but minimal.

The current forecast calls for it to start raining around 0100, followed by freezing rain, and then snow.

 As of 1517 this afternoon, the NWS was calling for 18"~24" of snow here. They'll issue and updated forecast Saturday morning.

So for now, it's The Calm Before The Storm......

Winter Storm Warning

 The weather's been pretty quiet these last few weeks. Had some snow flurries and a spot of rain, but otherwise not much going on.

That's about to change. The NWS issued a Winter Storm Warning a day or so ago, and it starts at 0500 om the 13th and goes to 0600 on the 15th. Starting tomorrow, there's a 70% chance of rain/snow, turning to 100% for Saturday and Sunday. Up until an hour or so ago all they were saying is the snow would be "heavy", but now they've added the expected amounts. They're calling for 24"~30", up from 6"~10", and winds over 30MPH.

That's NOT going to be pleasant to be out in, as this time of year with the temps in the high20's/low 30's, it's going to be heavy, wet snow, and stuff may get broken.

I have to drop SLW off at the big Medical Center here to have a test performed, and we'll stop on the way back (if she's not too groggy) to pick up a few things like some COFFEE, rawhide chews for the dog, and some diet soda for me.

Be safe out there!

OOOPS! It's Been Almost Two Weeks....!

 Just been busy, and haven't felt like posting. So much for my "try and post at least every three days" commitment. Oh, well....

The last two days have been fabulous; bright, sunny skies, moderate winds, and temps in the low 60's. I even got the garage swept out in preparation for Spring Cleaning! Hopefully this is a sign that Spring is rapidly approaching. I expect two more snows before the season is over. Usually one of them is heavy, wet snow that breaks branches and things, and the other one is a "Nuisance Level" storm.

This morning opened up overcast and drizzly, but it quit raining around 1600. Radar shows there's still a lot of rain out there, and some of it looks intense, due East of Denver, out towards the state line, but I don't think we'll get anymore tonight.

Work continues on the Heathkit transmitter, and I've taken pix of the work. Which has led me back down the Camera Rabbit Hole in search of a Nikon Macro lens. I have some excellent Nikon "General Purpose" lenses, and a couple of killer telephoto lenses, but nothing for close-up work, which is what Macro lenses excel at. I'll probably be getting one of these, a Nikon "AF-S FX Micro-Nikkor 60mm f/2.8G ED" lens, which seems to best fit using the selection guides on several websites, and my intended use. This one has some "ED" glass elements in it, which is to correct for chromatic (color) aberration, the blue and yellow fringing some lens designs produce out towards their edges. And it's an f/2.8, which means it has a very narrow Depth of Field wide open. This means it's very good at keeping the main subject is perfect focus, while softly blurring the background/foreground. It really makes the subject pop out of the picture. I can't get close enough sometimes with the lenses I have to get the subject to fill the frame, and this will allow that. They also work very well for portrait photography, so I'll get some Really Good Pix of The Little Guy this year.

 

And speaking of which, he celebrated birthday #4 last Saturday! We had a small gathering, and there was pizza, ice cream, and CAKE! A splendid time was had by all.

He's now gone through his "Paw Patrol" phase and moved on to Super Heroes. Sooooo, all the Paw Patrol toys have been packed away in a YUGE Rubbermaid Roughneck bin, and the former "Paw Patrol Room" is now the "Avengers Room". Yes, redecorating is involved. And seeing as the bedrooms are on the second floor here, and the basement storage area is in the basement (duh), I get 5 flights of cardio exercise with each round trip! Sweet Little Wife is now in the middle stages of planning for when grandchild #5 arrives. TLG's current bedroom is the smallest in the house, and with a little brother/sister coming, she's thinking of making the current Avengers Room into their bedroom, and reverting the smaller, middle bedroom to her use. So we're prowling Nextdoor.com and craigslist for some kid's furnishings.

 And he's discovered the Lego kits of various Super Hero vehicles and "accessories". These seem to be based on the hugely popular Lego Movies that people of a certain age group are fascinated by. These kits aren't your Father's Lego kits! They're much more akin to the "Snap Together" model cars of my youth. They use Lego-style pins and recesses to snap together, but there are many, many custom molded pieces for each kit, although most of the kits have common parts, usually molded in a different color.

I built this one last night, a Lego "Ironman Mech Suit", your basic Armored Fighting Suit.

And the assembled product. This is where a Macro lens shines. This was a close as I could focus, with my 18~70mm zoom lens all the way out to 70mm.

 It came in three bags of parts, and took about 30 minutes per bag to assemble. The front "breastplate" hinges down so you can put Tony at the controls, as shown above, but I'm sure Jarvis could run it remotely if requested.

I've also built the Lego Spiderman car, but I'm not sure where it is right now, maybe upstairs.

Yes, the probability of my stepping on a Lego piece in the dark, while barefoot, has gone up exponentially the last two weeks! TLG is very good about putting his stuff away. "Grandma's House = Grandma's Rules" works very well with him, and he has specific play areas where this stuff is allowed. But I'm sure there's a piece out there with my name on it. It might not be here yet, but it's out there.....

Hope y'all have a great upcoming weekend!
 

Return of Some Warmth

 Been busy hustling around with projects, SLW, and TLG. It got up to 46* today, so I took Pebbles the Wonder Dog out for a stroll. She hasn't been out of the backyard in several  weeks (hey, she's got a quarter acre to roam!), and was most anxious to re-sniff every inch of the path we take.

The tree carving project is completed, but that part of the yard is a mud pit, so I'll have to wait until things either dry out or freeze solid again so I can get out there and take some decent pix.

Spent all day playing with TLG, except for his nap time, and we had a ball doing Guy Stuff, like taking most of his Green Army Men, and cordoning off "The Blob" so we could get it back in it's container. The part of The Blob was played by today's guest star, Color Changing Green Slime. After dinner we played "Captain Hook and The Pirates", a free-form game made up as you go along.

"Arrrrrrgh, Matey! Heave To Whilst We Board Your Scurvy Vessel" was heard more than once, along with "Shiver Me Timbers", and "Walk The Plank Ye Scurvy Dog".

Great fun for all.

I even managed to get ten items listed on eBay. Several of them were posted as "Buy-It-Now" with what I thought were fair prices, and they sold within hours.

Think I'll get some Dogecoin with the eBay sales proceeds....

To The Moon!

Holy Moly, it's COLD!

 3.8* @ 2130 here, forecast to drop to -6*, and there's some flakes coming down.

It's not as cold as some places are reporting, but it's the coldest it's been this season, and we've got 2~4" of snow on the way.

Finally got the new 3-wire AC input socket installed on the SB-401 transmitter. It might look like it's not-quite-straight in the chassis, but it's not tightened down yet.

 Over the last week, I've built and installed three new media storage racks, and sorted out four U-Haul boxes of CD's and DVD's, and got them pretty much organized.

The lighter colored rack to the left is SLW's collection, properly arraigned alphabetically, and the two black ones on either side of the doorway are all of mine, arranged by genre.

This area was previously stacked with boxes and packing material, and now all the boxes have been flattened for easier storage, and the packing materials stored separately. I still have a ton of stuff to get rid of, and the boxes will get recycled to ship things in.

The area under the model car workbench was also stacked with boxes, and those have been taken care of, too. The bench will get cleaned up as the weather warms, and I can run the little cars outside again.

Plans for the weekend include hunkering down, having a fire, and watching a movie. TLG won't be here until Tuesday, as his Mommy and Daddy have a 3-day weekend together. BTW......the DIL is expecting again, with an August 20 due date. Fingers-crossed and prayers sent that she has an easier time, and goes full-term.

Friday Already?

 Geez, I should get out more often!

Had some "Bumps and Lumps and Down In the Dumps" the last week, so rather than work more on the transmitter (I did get the new AC socket installed), I decided to work on cleaning up the "Storage Room" in the basement. Found some things I haven't seen since we moved here, and started sorting stuff out.

I now have another huge box of clothing to donate to our local ARC Thrift Store, several boxes of electronic "stuff" have been reduced to one box, and I have a whole bunch of somewhat rare, obscure T-Shirts to sort through from my rocket chucking days. I'm only going to keep the ones with the best graphics, and that means those with just the name of the satellite or mission name on them will be hitting ePay for disposal. I have more than enough plain, white T-Shirts with obscure logos where a pocket should be, and I don't need more. If they don't sell, they'll go to the Thrift Store.

And I dug out all the APC UPS units I have, and will probably put them on the "Come And Get It!" email list the local Ham Radio Club has. I kept the two with the newest batteries plugged in since we moved here, but they all should have new batteries installed. 

I gave away a Systron-Donner 1702 Signal Generator and a Tektronix 492 Spectrum Analyzer I posted on the list last week, and that opened up some floor space, and now with the UPS units moved out, I freed up some more. 

Now there's plenty of room for Pebbles' dog bed in the shop, and I'm sure she'll appreciate it.

SB-401 Transmitter Rebuild Progress - Part 6 -

 In which I joyously announce all the switch contacts are cleaned!

 I have no idea why I took that picture, when the switch to the right of it shows a whole row of cleaned contacts to impress you with. Oh, well...

And all the rotary controls have been cleaned and lubricated, and more glaring examples of Poor Workmanship have been corrected.

And I started on the next item on the punch list, updating the AC Input connector. I removed the original connector, and penciled-in the cut-lines for the new one.

After I get the new connector installed, I'll start moving on to the Power Supplies in the radio. All new manufacture filter caps will be installed, followed by new rectifier diodes with higher ratings. The original diodes were rated 750 Volts PIV and 750mA Forward Current, while the replacements are rated at 1000 Volts PIV, and 3 Amps forward current. A bit overkill on the current ratings, but I have good supply of 1N5408 diodes from the little place back in Torrance I used to get items like that from.

And it's forecast to be sunny and in the low 60's tomorrow. Probably ought to get Sweet Little Wife's snow tires on. I think we're gonna have a slushy/snowy rest-of-the-winter.

SB-401 Transmitter Rebuild Progress - Part 5 -

 In which Murphy walks in the shop, dumps over my coffee, and laughs......

Well, I hit a snag in the process of removing the knobs on the control panel so I can free the control panel from the chassis, and repair the dial mechanism. It's an identical procedure to what I did on the receiver, but this time one of the knobs fought me. It uses a small, Allen-drive setscrew to secure it on the shaft. It takes an .050" Allen wrench to get it loose. And the setscrew is in an awkward position, meaning it's hard to get the teeny-tiny Allen wrench all the way into the setscrew to tighten and loosen it. Most people don't get the wrench fully bottomed out, and they round the corners of the wrench, and round the corners of the setscrew, meaning it gets very difficult to get the setscrew loose.

I tried brand-new wrenches with sharp corners, grinding an older wrench so the rounded off part was removed, heating the metal insert the setscrew threads into, and lots of other things, including turning the knob a bit too hard.........POP!....there goes the coffee....

I broke the little "paddle" off the knob by pushing on it with my thumb, and it shot off across the shop towards The Place Where 10mm Sockets Go To Die......

The bright green color is where the "paddle" that hangs down used to go. So now I HAVE to get the knob off so I can replace it. I was able to easily cut off the green plastic, and then attacked the aluminum insert the setscrew threads into.

Took a good 90 minutes of gently cutting away parts of the aluminum insert so I could "split" it, release the tension provided by the setscrew, and slide it off the shaft.

You can see the setscrew sitting there laughing at me....

So finally, and with minimal collateral damage, I got the insert off the shaft.

In other news, The Brown Truck of Happiness stopped by today with a load of Thermionic Devices of types I didn't have, so at least some things are progressing.

Too bad we can't "Reload" tubes when they get used up.

Enjoy your weekend!

SB-401 Transmitter Rebuild Progress - Part 4 -

 Got the new BNC connector all squared away, and replaced the mismatched hardware on the SO-239 RF Output connector. Still waiting on parts because I can't locate a couple I thought I had.

So I went on to my favorite pastime lately, cleaning wafer switches.

This is the Function Switch, all cleaned and lubed.

Before I got started cleaning the switches, I went through the whole chassis tightening hardware. Seems like every time I put a screwdriver or 1/4" nut driver on a piece of hardware, it was loose. Sometimes maybe an 1/8th of a turn, usually about 1/4 turn loose, and a couple that were over a full turn loose, which is definitely in the "Finger Tight" category. Since most of these either grounded the periphery of a printed circuit board, or were securing a ground lug/terminal strip, it was critical to get them all nice and snug again.

And while doing that, the occasional example of Poor Workmanship popped up, like this wire crudely stuck through the terminal and "soldered" in place.

Judging from how "well" the solder flowed onto the bare wire, I'd say this is either a bad solder joint, or about to be one. This is on the Bandswitch, and poor soldering here can cause all kinds of grief down the road. 

What I've been doing to help prevent that is cleaning/flushing/treating each wafer separately, and then wicking off all the solder, cleaning the wire and terminal, applying a very small amount of new "Flux, Rosin, Type RMA", and resoldering each connection on that wafer.

And you can see how dirty the rotary and stationary contacts are compared to the above picture.

We got about 2" of snow last night, and tonight as of 2330, it's down to 15*. Makes me glad the new track has remote start in case we have to go somewhere. One thing I've noticed is how fast this engine warms up. I'll get in the car in 15~20* weather, start it up, and by the time I'm buckled in and a block away, the temp gauge is up off the peg, and the heater is beginning to blow warm air. One of the things all the manufacturers do these days is to get the engine up to operating temp ASAP, as it greatly aids emissions reduction, and this is a side benefit.

SB-401 Transmitter Rebuild Progress - Part 3 -

 Managed to get a few things done today while The Little Guy was napping, and after he went to bed. 

I can't believe how much energy TLG has. One minute we're zooming around playing "Pirates", and the next we're in his "Paw Patrol" room building Lego structures we can smash vehicles into. Or he'll get out his big plush Godzilla, and wade through the center of (his little) town.

Great fun, and today we also played "The Blob", starring Green Army Men with misc Paw Patrol characters, and tonight's special guest star, "Purple Slime" as "The Blob".

While playing "Pirates", character "Jack", his glittery skull with light up, flashing, color-changing LED eyes quit working. That entailed a small side trip down to the Electronics Shop where we "performed surgery" on Jack. Old Jack needed an emergency battery-ectomy, and after the patient was safely in PostOp, TLG broke out in a great big smile and thanked me for "saving Jack's life". TLG was an excellent Assisting Doctor, handing me the instruments I asked for (really...he knows the difference between a cross-point and a flat-blade screwdriver!), and watching intently as we operated on Jack. He loves watching me when I'm fixing something of his or Grandmas, and it usually involves small tools, batteries, and/or glue. He's not to the stage of asking "WHY?" yet, but I'll do my best to keep him quite entertained with little demonstrations and experiments when he does.

I started on some of the "mechanical" work on the transmitter today, like tightening ALL the chassis hardware, and 90% was loose. Not "finger loose", but anywhere from an eighth-of-a-turn loose to a quarter-turn loose, which is pretty loose when it involves grounds, like most of these were.

Then I pulled the AC Input socket so I can open up the hole and replace it.

 Another connector I'm changing is the Receiver Antenna jack, which is an RCA phono jack, just like on the receiver I just finished.

Here's the new BNC in place, with the OEM connector above it. The red wire gets moved to the center pin of the new BNC connector.

 And this is where our friend Murphy sticks his head in the shop....

See the nut? See the shield wall? See any room for the nut to turn, let alone get a wrench on it? Yeah, I don't either.

The wrench flat of the nut is zero-clearance with the shield wall running vertically. Now at some time, I had a "Special Service Tool" that was a socket that slipped over the outside of the BNC connector, grabbed on to the two bayonet pins, and let you crank down the nut on the back of the connector as tight as you pleased. It was such a cool tool for Radio Guys, that I've bought several of them over the years. They either get loaned out and never returned, they just "disappear", or in some cases I gave/sold a couple to people.

And now I can't find the one I thought I still had! RATS! Time to improvise here....

Start with some generic BNC I have a bunch of that has a male plug as part of it:

Clamp it in a vise:

 Attack it with my Dremel and Mr. Cutoff Wheel:

And wind up with just the Coupling Nut part:

Which nicely fits on the new Receiver Antenna jack, and lets me use a small pair of Channellocks to get it nice and tight. The oddball, mismatched hardware holding on the big connector to the right of the new one will be replaced with new cross-point hardware.

I ordered all the replacement tubes I needed today, and several each of the others unique to this radio. I also ordered some more of the AC Input sockets, as I can't find any of the others I thought I'd bought before we moved here. Seeing as I've been doing "Deep Dives" into my parts stock the last week or so I would have figured I'd find them, but no soap. I have found some things I thought were lost forever, and I'm finally getting the parts at least sorted into categories, like "Resistors", "Capacitors"< "Diodes", and things like that.

So for the next few days I'll be busy cleaning and lubing all the switches, looking for poor soldering/sloppy workmanship issues to correct, tightening hardware, and doing the whole "Mechanical Dial Alignment" procedure like I did on the receiver.

To motivate myself to keep going, I moved my "#1 Boat Anchor Station" upstairs, and plunked them on the operating bench.

I really want to get these two guys rebuilt. These were what I would have gotten instead of the Heathkit rigs if money had been no object.

SB-401 Transmitter Rebuild Progress - Part 2 -

 The power transformer about threw me for a loop, as when I looked at the first pictures of the radio, I noticed what appeared to be tar leaking out, generally an indication that the transformer has been overheated, either by a component failure, or due to a shorted turn in the transformer itself. Closer inspection revealed the "tar" was the insulating varnish used when the transformer was manufactured.

This is the picture that gave me pause. The bottom side of the transformer is the black rectangular object with the green, red, and blue fabric-covered wires coming out of it. It also looks like something "leaked" out of the transformer, which I immediately assumed (from the picture) was tar.

WELL....happy, happy, joy, joy, it's not tar. When I went back to examine things closer, I noticed the same "globby" looking stuff on the top of the transformer, and that's when I realized what it was.

 It even shows up in the assembly manual, as this picture of the picture in the manual shows.

Here's a side-view of the power transformer showing how thick the coating is.

So, with the transformer cleared as fit-for-service, I proceeded to test all the tubes.

OOPS....got three bad ones, all leaky. Not shorted, but leaky in the Megohm range, which means toss it. I had one of the tubes in stock, but the others will have to be ordered. Not a big deal, as they're readily available, and since the two I don't have are also used in my Drake T-4XB transmitter, and my Hallicrafters HT-44 transmitter, I'll order up a half-dozen. I should probably also refill my 6AU6 stock, as they're also used in my other radios, and the SB-301 receiver needed one, and now this transmitter needed another one.

And I still can't find my doggone RF Probe, so I'm either going to build one in a little Pomona box, or price out and order another. The Heathkit probe works, and is accurate, but it has a huge probe tip, and is cumbersome.

The Little Guy will be here for his Sunday overnight, so I'll have to confine my work activities to his nap times and after his bedtime, if he hasn't completely worn me out!